Catálogos >
SCHAKO KG >
BSK-RPR

BSK-RPR
60Páginas

Extractos del catálogo

Technical documentation Installation, mounting and operating instructions BSK-RPR Fire damper Fig.: BSK-RPR with B10 drive USABILITY CERTIFICATES • • • Performance Reliability Certificate according to EU-Bau PVO 0761 – CPR – 0245 EC Certificate of Conformity 0761 – CPD – 0263 Declaration of Performance DoP-BSK-RPR-2017-08-09 PERFORMANCE DATA • • For automatic locking of fire lobbies For use or connection of a smoke release device with abZ (e.g. SCHAKO smoke detection system RMS) in connection with suitable release devices (e.g. spring return actuator) SPECIAL FEATURES CLASSIFICATION AND STANDARDS • • • Classification according to EN 13501-3, depending on the mounting situation EI 90 (ve, ho i↔o) S Product standard EN 15650 Test standard EN 1366-2 SCHAKO | Ferdinand Schad KG Steigstraße 25-27 D-78600 Kolbingen ATEX version available (at an extra charge) Extensive uses and applications Housing leakage class C according to EN 1751 For optimum integration into the building control system via the SCHAKO EasyBus signalling and switching bus system or the SCHAKO BKSYS fire damper mini-controller

Abrir la página 1 del catálogo

Fire Damper Model BSK-RPR Technical documentation Table of Contents Construction subject to change. No return possible

Abrir la página 2 del catálogo

Fire Damper Model BSK-RPR Technical documentation Description DESCRIPTION Fire dampers, installed in ventilation ducts (air conditioning systems), serve for the automatic locking of fire lobbies. The fire damper BSK-RPR corresponds to EN 15650, EN 135013 and EN 1366-2. The BSK-RPR has been tested according to EN 1366-2 in compliance with Declaration of Performance no. DoP-BSK-RPR-201708-09. It has the Performance Reliability Certificate according to EU-Bau PVO 0761-CPR-0245 and the EC Certificate of Conformity 0761-CPD-0263. Its category according to EN 13501-3 is EI 90 (ve, ho i ↔ o) S....

Abrir la página 3 del catálogo

Fire Damper Model BSK-RPR Technical documentation Models and dimensions MODELS AND DIMENSIONS BSK-RPR – Nominal sizes 100 to ≤ 250 BSK-RPR-S (plug-in connection) Fig. 1: Dimension BSK-RPR-S – Nominal sizes 100 to ≤ 250 BSK-RPR-S with mounting frame AR (Mounting frame AR only possible in -S design, pre-mounted ex works, delivery in loose form not possible) Fig. 2: Dimension BSK-RPR-S with mounting frame AR – Nominal sizes 100 to ≤ 250 BSK-RPR-F (flanged connection) Fig. 3: Dimension BSK-RPR-F – Nominal sizes 100 to ≤ 250 1 2 3 4 Housing Damper leaf Hand lever Locking profile Construction...

Abrir la página 4 del catálogo

Fire Damper Model BSK-RPR Technical documentation Models and dimensions BSK-RPR – Nominal sizes > 250 to 500 BSK-RPR-S (plug-in connection) Fig. 4: Dimension BSK-RPR-S – Nominal sizes >250 to 500 BSK-RPR-S with mounting frame AR (Mounting frame AR only possible in -S design, premounted ex works, delivery in loose form not possible) Fig. 5: Dimension BSK-RPR-S with AR – Nominal sizes > 250 to 500 BSK-RPR-F (flanged connection) Fig. 6: Dimension BSK-RPR-F – Nominal sizes > 250 to 500 1 2 3 4 Housing Damper leaf Hand lever Locking profile Construction subject to change. No return possible...

Abrir la página 5 del catálogo

Fire Damper Model BSK-RPR Technical documentation Models and dimensions Rubber lip seal for BSK-RPR-S Model BSK-RPR-S is delivered as standard with a rubber lip seal. Flange bores BSK-RPR-F SCHAKO ASG-RF / VT-RF / FS-RF: Flange bores suitable for BSK-RPR-F Fig. 8: Release device BSK-RPR Construction subject to change. No return possible

Abrir la página 6 del catálogo

Fire Damper Model BSK-RPR Technical documentation Models and dimensions Damper leaf projecting ends Nominal size * Extension piece (on site) necessary Table 3: Damper leaf projecting ends BSK-RPR-S "a"= 50 Minimum distance between the front edge mm: of the open damper leaf and the security grille (ASG) or flexible connection piece (FS). Nominal size * Extension piece (VT-RF) necessary Table 4: Damper leaf projecting ends BSK-RPR-F Construction subject to change. No return possible

Abrir la página 7 del catálogo

Fire Damper Model BSK-RPR Technical documentation Models and dimensions UseThe fire damper type BSK-RPR can be fitted as shown in the following table. Use 1) Installation only in connection with a ventilation duct devoid of openings (fire resistance duration 90 min.) between the BSK-RPR and the fire-resistant wall to be protected. Mounting only allowed in conjunction with mounting frame AR. 2) The exact wall thickness/es must be taken into account and specified when ordering. For installation, the accessories for sliding ceiling connection plus mounting frame AR are required. 3) At nominal...

Abrir la página 8 del catálogo

Fire Damper Model BSK-RPR Technical documentation Installation details General information • During mounting or installation, there is a risk of injuries. To avoid any possible injuries, personal protective equip-ment (PPE) must be worn. • Fire dampers must be installed such that external forces do not impair their permanent functioning. During mounting it may be required to provide reinforcements for the housing or the like. The requirement of statically load-bearing lintels may have to be taken into consideration. • Improper transport/handling may result in damage/func-tional impairment....

Abrir la página 9 del catálogo

Fire Damper Model BSK-RPR Technical documentation Installation details Installation on solid walls with mounting frame AR Nominal sizes 100 to 500 - (dry installation)  Installation on solid walls (shaft walls, shafts, ducts and fire walls) made of, for example, concrete, masonry according to EN 1996 or DIN 1053; solid plaster wall boards according to EN 12859 or DIN 18163; apparent density ≥ 450 kg/m³ and wall thickness W ≥ 100 mm only in conjunction with mounting frame AR.  The distance of the fire dampers to one another must be at least 200 mm. (For nominal sizes 100 - 250, mounting is...

Abrir la página 10 del catálogo

Fire Damper Model BSK-RPR Technical documentation Installation details Installation away from solid walls with mounting frame AR Nominal sizes 100 to 500 - (dry installation)  Installation away from solid walls (shaft walls, shafts, ducts and fire walls) made of, for example, concrete, masonry according to EN 1996 or DIN 1053; solid plaster wall boards according to EN 12859 or DIN 18163; apparent density ≥ 450 kg/m³ and wall thickness W ≥ 100 mm only in conjunction with mounting frame AR.  When fitting the fire damper away from solid walls, it must be suspended from the ceiling. ...

Abrir la página 11 del catálogo